RB26DETT Torque Specs

By -




RB26 Torque Specs

Crank Bolt – 329-344 ft-lb

Timing belt cover – 2.2-3.6 ft-lb

Timing Belt Tensioner – 32-43 ft-lb (nut-conical washer-washer)

Idler Pulley – 32-43 ft-lb

Head bolts – 22 ft-lb, then 80 ft-lb, loosen all bolts, 22 ft-lb, then 76-83 ft-lb

M6x1.0 Head Bolt – 4.6-6.1 ft-lb

CAS bracket – 15-20 ft-lb

Cam Pulley – 10-14 ft-lb

Cam Cap – 6.7-8.7 ft-lb (Page 89 in FSM PDF)

Timing Cover Back Plate – M6 bolts – 4.6-6.1 ft-lb, M8 bolts – 12-15 ft-lb

Timing Belt Cover – Upper & lower 2.2-3.6 ft-lb (Page 76 in FSM PDF)

Crank Angle Sensor (CAS) bolt – 12-15 ft-lb

Water Pump – M6 4.6-6.1 ft-lb, M8 12-15 ft-lb, M10 23-31 ft-lb (do in order page 101 in FSM PDF)

Thermostat Housing – 12-15 ft-lb

Throttle Cable adjust – 5.8-7.2 ft-lb

Engine Mounts – 32-41 ft-lb

Oil Pump Screws and Regulator – Screws 2.7-3.7 ft-lbs, Reg Plug 29-51 ft-lb

Oil Pump to block – 6.7-8.7 ft-lb

Oil Pan – M6 (oil pan/rear main) 4.6-6.1 ft-lb, M10 nuts and bolts – 23-31 ft-lb (in order Page 110 in FSM PDF)

Oil pickup tube/strainer – M6 bolt 4.6-6.1 ft-lb, M8 bolts 12-15 ft-lb

Oil baffle plate – 4.6-6.1 ft-lb

Drain Plug – 22-29 ft-lb

Knock Sensor – 12-15 ft-lb

Oil Jets – 22-30 ft-lb

Power Steering pump bracket – 27-37 ft-lb

Flywheel bolts – 105-112 ft-lb

Main Bearing Bolts – 34-38 ft-lb (In order, Page 127 in FSM PDF)

Connecting Rod Bolts – 10-12 ft-lb , then 60-65 degrees angle (Page 122 in FSM PDF)

Windage Trays / Girdle Baffle Plates– 4.6-6.1 ft-lb

Rear Main Plate – 4.6-6.1 ft-lb

Pressure Plate to Flywheel – 25-33 ft-lb

Intake Manifold – 12-15 ft-lb (tighten inside to outside Page 50 & 58 in FSM PDF)

Air Intake / Water Temp Sensor – 14-22 ft-lb

Exhaust / Turbo Manifold – 13-17 ft-lb (tighten inside to outside Page 72 in FSM PDF)

Spark Plugs – 14-22 ft-lb

Ignition Coil Brackets – 6.7-8.7 ft-lb

Valve Cover Screws – 1.4-2.9 ft-lb (tighten inside to outside Page 75 in FSM PDF)

 




OTHER INFO:

Fuses and Relays – Page 762 in FSM PDF

Torques Chart – Page 764 & 771 in FSM PDF

Fluids Chart – Page 770 in FSM PDF

flowgoode

2 Comments to RB26DETT Torque Specs

Leave a Reply

Your email address will not be published. Required fields are marked *